Team Integra Forums - Team Integra - codenamezero
Old
Rating: 2 votes, 1.00 average.

DIY: Wideband O2 installation and wiring

Posted 07-19-2010 at 11:25 PM by codenamezero

This article is to show you one way of routing the Wideband O2 sensor through the firewall into the passenger side floor area.

Before we start, I would like to thank sgtmillhouse648 and MeltMan for helping me solve the problems that i encountered during and after the install. Thank you!


Step 1
First we remove the battery and the battery support tray. Once they are removed, you should see something similar to my picture below. If you have AC, you will...
Senior Member
Views 21361 Comments 4 codenamezero is offline Edit Tags
Old

DIY: Wideband O2 harness

Posted 06-19-2010 at 01:39 PM by codenamezero
Updated 08-29-2011 at 12:02 AM by codenamezero

This is to give you a general idea on how to build the wideband O2 (WBO2) sensor harness for the NAW_7S WBO2 controller.

The NAW_7S user manual already have a similar guide to show you how to do it, however i sorta disagree with some of the information and i want to point out some of the problems i encountered in the process... so i am writing an article instead.

Tools:
  • Crimping tool
  • Soldering tool and soldering iron
  • 22-18* GA wire, minimum 6 x 4 feet
  • Connector
...
Senior Member
Views 6121 Comments 0 codenamezero is offline Edit Tags
Old

DIY: G3 Lower Clutch Line replacement

Posted 05-15-2010 at 12:02 AM by codenamezero

I've had my 99 teg for almost 8 years. About 2-3 years ago, the clutch become squeaky, i would flush the clutch, the noise will be gone for 2-3 months, and it will quickly come back again.
It was very annoying. It wasn't the clutch pedal, I've lube everything properly, and i didn't think it was my CMC because as soon as i change my fluid, the noise went away...
So i suspect it was something else... I've noticed my fluid would become murky very quickly, and i begin to wonder why......
Senior Member
Views 12684 Comments 2 codenamezero is offline Edit Tags
Old

S300 Beginner Guide

Posted 03-23-2010 at 09:38 PM by codenamezero

Do you want to tune your car? Have you decided to use Hondata S300? Want to find out, read up, or get an idea on what is needed before spending your hard earn 550-700$? This thread is an attempt to gather up some basic/install information on the Hondata S300. I had a hard time finding out and trobleshoot problems i have during my installation, so hopefully this could help someone else out there.

Getting started
- ECU (Chip) Basics
- s300 Overview
- Find out which ECU you need for your motor/car...
Senior Member
Posted in Tuning
Views 36335 Comments 0 codenamezero is offline Edit Tags
Old

G4 (RSX) Wheel bearing, Trailing arm replacement

Posted 09-12-2007 at 07:03 PM by codenamezero

This article can potentially show you how to replace the G4 (RSX):
- rear brake rotor
- rear wheel bearing
- rear wheel sensor
- rear upper control arm
- rear lower control arm


Tools you need:
- Socket wrench #10, 12, 14, 16, 17, 19, 24 (or was it 22?)
- Breaker bar
- Big ass hammer
- Long and big, flat head screw driver (for prying purposes)
- Hex allen key - WD40 or similar
- Anti-seize compound...
Senior Member
Posted in Brakes
Views 9740 Comments 0 codenamezero is offline Edit Tags
 
For the best viewing experience please update your browser to Google Chrome